NOTE: THERE IS NOW A NEW REVISED VERSION OF THIS PROJECT WHICH IS THE BETTER OPTION TO GO FOR IF YOU'RE PLANNING ON BUILDING THIS PROJECT.
CLICK HERE TO GO TO PROJECT 51, THE SAMPLE & HOLD VERSION 2.
This doesn't mean the design in this article doesn't work well. On the contrary. It works very well but the new one is better designed and has a better output impedance so it's more stable when connected to other modules. So for a S&H you really should build project 51. It uses the same components as this version. I'm leaving this old version online as an archived article so people who built it can refer back to it.
Original text:
Every synth needs a sample and hold circuit in my opinion to have an extra source of control voltages. The S&H samples a voltage when triggered and holds that voltage until it is triggered again. If you feed it a white noise signal it will give you random voltages on the output which can create random tones if you input that signal into a VCO. If you feed it a signal from the LFO it will turn that signal into a stepped signal. The LF398 chip samples the input signal in 4 to 20 millionth of a second (!) and is used in many more applications that just synthesizers.
For this build I used the schematics from Rene Schmitz called 'Yet Another Sample and Hold'. (<-- click to have a look at the schematic)
I had ordered the LF398 chips a while ago and had a try earlier at building this circuit but I couldn't get it to work, but this time everything went fine and the circuit works very well. I added some extra's to this circuit in the form of a DC offset feature so I can control the voltage range of the output signals a bit better and I installed two input sockets between which you can choose with a SPDT switch. I also installed a switch that gives me the normal output voltage range (0 - 10Vpp) or half the normal output voltage range (0-5Vpp) which is better as input for the VCO's. The DC Offset in particular has proven to be a very useful addition. If you turn it into the negative the random notes get very deep and if you then put that through, say, the Steiner-Parker filter, you get the most amazing sounding low notes that sound really deep and sharp and in some cases can resemble the sound of drops of water if you put reverb on it. I can experiment for hours with this module.
At first I used a potmeter with center detent for the OffSet control but I later decided to change it back to a normal one because it was difficult to set the offset accurately with the center detent spring pulling on the potmeter around the middle setting.
For this build I used the schematics from Rene Schmitz called 'Yet Another Sample and Hold'. (<-- click to have a look at the schematic)
I had ordered the LF398 chips a while ago and had a try earlier at building this circuit but I couldn't get it to work, but this time everything went fine and the circuit works very well. I added some extra's to this circuit in the form of a DC offset feature so I can control the voltage range of the output signals a bit better and I installed two input sockets between which you can choose with a SPDT switch. I also installed a switch that gives me the normal output voltage range (0 - 10Vpp) or half the normal output voltage range (0-5Vpp) which is better as input for the VCO's. The DC Offset in particular has proven to be a very useful addition. If you turn it into the negative the random notes get very deep and if you then put that through, say, the Steiner-Parker filter, you get the most amazing sounding low notes that sound really deep and sharp and in some cases can resemble the sound of drops of water if you put reverb on it. I can experiment for hours with this module.
This module will work fine on both +/-15V or +/-12V.
Here's the layout. All green wirebridges refer to connections to ground. All potmeters viewed from the front:
(Last revised: 19-Aug.-2021: Cosmetic changes to layout)
At the bottom right on the layout you can see the circuit for the DC Offset feature. I re-designed this from the previous version. This is a better way to add DC offset and it makes use of both opamps in the TL072 chip. (You can also use a TL082).
Here's a close-up of just the stripboard:
This S&H has an internal clock pulse generator based around one Schmitt Trigger NAND gate of the CD4093. You can also choose to trigger it externally by selecting the external input with switch S1.
Here's the schematic drawing of the extra features I added myself; the DC-Offset and the output range switch. A very observant reader noted that my output range switch does alter the low impedance that the normal opamp output would provide and this might be problematic in some cases. He suggests to put the range option in between the two opamps (see comments below). My reasoning is that the signal from this S&H usually goes back into an opamp like the CV input of a VCO or of a filter and most of the times these are opamp buffered and those inputs have an infinitely high input impedance so in those cases it really doesn't matter, but if the signal goes into an opamp inverter with resistors than that resistor balance can be upset. That's nothing serious but it would mean the amplitude of the S&H signal can be influenced in a way not anticipated.
Here's the layout. All green wirebridges refer to connections to ground. All potmeters viewed from the front:
At the bottom right on the layout you can see the circuit for the DC Offset feature. I re-designed this from the previous version. This is a better way to add DC offset and it makes use of both opamps in the TL072 chip. (You can also use a TL082).
Here's a close-up of just the stripboard:
Here's the schematic drawing of the extra features I added myself; the DC-Offset and the output range switch. A very observant reader noted that my output range switch does alter the low impedance that the normal opamp output would provide and this might be problematic in some cases. He suggests to put the range option in between the two opamps (see comments below). My reasoning is that the signal from this S&H usually goes back into an opamp like the CV input of a VCO or of a filter and most of the times these are opamp buffered and those inputs have an infinitely high input impedance so in those cases it really doesn't matter, but if the signal goes into an opamp inverter with resistors than that resistor balance can be upset. That's nothing serious but it would mean the amplitude of the S&H signal can be influenced in a way not anticipated.
If that's all gibberish to you just ignore it and proceed building ^___^
[EDIT: This is one of the reason I re-designed this project in early 2023 and wrote a new article about it (project 51). I'm keeping this article online because this is an archive of the modules I built and the progress I made over the years and as reference for people who already built this project in case they need to refer back to the schematics or layout.)
At first I used a potmeter with center detent for the OffSet control but I later decided to change it back to a normal one because it was difficult to set the offset accurately with the center detent spring pulling on the potmeter around the middle setting.
The CV output goes through a resistor voltage devider that halfs the output voltage. This puts the different random tones closer together which sounds better. It's something I added after testing and seeing the output signals on the oscilloscope. Later on I added a switch that bridges that voltage devider and gives the original output voltages. I labeled it "Output x 1 and x 0,5". I did this because I wanted the full voltage available in case I want to use the output of the S&H to control the Cut-Off frequency of a filter (among other things). The resistor voltage devider however is something I strongly advise to include in your circuit if you're building one of these. The range switch is a good feature to have.
I didn't have any more space in the synthesizer I build to put this S&H in as a separate module so I cut a hole in the wood above the panels and mounted it there. This works very well and adds yet more buttons and switches and a flashing light. That always looks cool ^___^
Here's a picture of the finished panel and one that shows the placement within the synthesizer:
Here's a little video to demonstrate the sound you get when you put white noise on the input. This sound is going through the Dual Korg MS-20 filter described in the previous article.:
I didn't have any more space in the synthesizer I build to put this S&H in as a separate module so I cut a hole in the wood above the panels and mounted it there. This works very well and adds yet more buttons and switches and a flashing light. That always looks cool ^___^
Here's a picture of the finished panel and one that shows the placement within the synthesizer:
Here's a little video to demonstrate the sound you get when you put white noise on the input. This sound is going through the Dual Korg MS-20 filter described in the previous article.:
Here's a cool demonstration of the S&H with the Triple Wavefolder and the Steiner-Parker filter:
Okay that's another one done. Hope you enjoyed it and if you did please consider following this blog to get notified of new uploads and while you're here, leave me a comment please!
If you want to know more about sample and hold circuits I refer you to this Wikipedia page.
Here's a link to the LF398 sample and hold chip datasheet in PDF form: (Click here)
If you want to know more about sample and hold circuits I refer you to this Wikipedia page.
Here's a link to the LF398 sample and hold chip datasheet in PDF form: (Click here)
The DIY Modular Sessions YouTube channel made some videos about building this sample and hold module which you can watch by clicking the links below:
PART-1 Preparing the stripboard
PART-2 Soldering the components in.