Synthesizer Build part-50: UTILITY LFO for EURORACK.

This is the Ken Stone Utility LFO, the bigger version of project 47 with an extra feature that I added. I managed to make the stripboard even smaller than the 'Simple Dual LFO' so it fits even the 'Nifty Case' Eurorack skiff. The LFO has the following waveforms: Pulse, Square, Saw to Triangle to Rampwave and a Variable output which has a mix between Square and Triangle/Saw/Ramp waves. I later added a mini-mixer that adds the two variable outputs together to get even weirder waveforms.

An other LFO might not be the most exciting of projects but I think this LFO will be worth it because of the weird waveforms it can make and because I realized, now that I have my own Eurorack system, that modulation sources are important to have. To quote a popular YouTuber: Modulation is what makes Eurorack interesting. I even added a feature of my own later on. It's the ability to mix both variable outputs together to get a variable A+B output. That's at the bottom of this article.

The Dual LFO from project 47 is just the first two stages of the Utility LFO without the mixing stage. Because I actually use the Dual mixer in my Eurorack setup and I loved the idea of having the full Utility LFO available, I thought I'd build the whole LFO this time and try and make it as small as possible. It is 49mm deep and the panel is 9HP wide (4.5 centimeter). This is a bi-polar LFO meaning the waveforms go both positive and negative in voltage.

This LFO does not have a sync option but this is a really useful LFO for a Eurorack system because it has not only the normal waveforms you'd expect but the option to merge waveforms together which makes for some very weird modulation possibilities. And because this is a Dual LFO you could mix the 2 variable waveform outputs together in a Multiple and make even weirder shaped waveforms. That mixing needs to be done outside of this module though. I couldn't fit that inside this design. This LFO would pair really well with the Dual Voltage Processor for that reason.

I managed to get everything on an 18 by 24 hole wide piece of stripboard. Six potmeters and eight output sockets on the panel, and an extra little print for the two bi-colour rate indicator LEDs which I made separate from the main print just like on the Dual LFO and as mentioned before a second little print to mix the two variable outputs together. The panel I made for it is 9 HP wide (4.5 centimeter). You might be able to make it even smaller if you use smaller potmeters in the panel. Even though I included an L-Bracket in the layout, I didn't use one. The stripboard is actually hot-glued in place in between the two columns of potmeters straight to the back of the panel making sure no copper strips make contact with the metal of the panel. I did this to keep the overall depth of the module as low as possible.

I did not include a Eurorack power connector on the print although there is room enough left to put one in. Instead I made a powercord with a Eurorack connector at the end so it always stays connected to the stripboard. This is handier because eurorack ribbon cables take up space too and this is a smaller footprint solution with only three thin wires.

This is mainly a Eurorack project but naturally this circuit will work just as well in a Kosmo sized synthesizer. I optimized the circuit to run on +/-12V but it was originally intended to be run on +/-15V. You will get higher amplitude waveforms when you run this on a dual 15V powersupply so if that's a problem for you, you can change the 1K8 resistors I used on the waveform outputs back to the 1K's you see in the schematic. The original schematic uses +/-15V.

SCHEMATIC:

Below is the schematic I used for my layout. I put in bigger timing capacitors because I wanted one LFO running really slow and the other to about 20Hz. That is more useful for my modulation needs but you might want different values so I strongly advise you to do some testing with different capacitor values to get the LFO in the frequency range you desire.

The types of quad opamps and the one dual opamp used in this project are not critical. The schematic calls for TL074 and TL072 opamps but you can use anything with the same pinout. I used two LM324's and an NE5532 dual opamp. Btw, I did not include the transistor with the rate LED as seen on the schematic but I designed my own circuit for that so I could use bi-coloured LED's. It's just two opamp voltage followers (or buffers) feeding the LED's with the signal from the Pulse output. You can connect them to any output you wish but the pulse is the clearest for the LED's.

Here's the schematic drawing. Beware the opamp numbering does not follow the opamp order I used in the layout.

  

LAYOUTS:

Below are the layouts I made for this project. As ever they are verified. I used them for my build. I changed the order of the opamps used from the order on the schematic. I setup one LFO using all the opamps on the left hand side and the other LFO using all the opamps on the righthand side of the IC's on the stripboard. That made it more compact plus easier to keep the overview. Luckily I did not need to make any changes or do any troubleshooting. I built it and tested it and everything worked first go.

You need four 100K and two 500K linear panel potmeters to this project. Measure and test them before you use them. That can save you some troubleshooting later. If you plan on mounting the stripboard to the panel with hot-glue like I did then try to solder the hook-up wires of the righthand side (the side that's glued to the front panel) as far to the middle as possible so you can still get to them once the stripboard is glued in place. This won't be possible with all wires but try. You could also solder them straight to the back/copper side.

Wiring diagram:

Stripboard only view:

Here are the cuts and wirebridges as seen from the component side! As always, I advise to mark the cuts on the component side first with a black waterproof marker pen and then put a pin through the marked holes and mark them again on the copper side. Then you can make the cuts accurately and you can see where the cuts are when you're soldering in the components.

Bill of materials. 

The timing capacitors listed were chosen for my specific needs. I advise you to go by the schematic (47nF) or else test and determine the best values for your needs. You can use the Falstad simulation linked at the bottom of the article to test different values before building.

No bypass caps are included in this BOM because I didn't use any. They are on the schematic and you can put 100nF caps over the power connections on the IC's to ground if you want to. To do all IC's you'd need six 100nF ceramic caps (you don't have to do the LED driver IC).

This BOM does not include the components for the little mixer I added on further down the article. For that you will need 4 x 100K resistors, a 1K resistor and a 200K trimpot and a TL072 dual opamp.

PICTURES:

Here are some pictures of the build proces and the panel I made for it. I had some fill-in panels left from when I bought my 'Nifty Case' Eurorack case and I used one of them to make my front panel. It was already cut to the right height so ideal for this project ^___^  All I had to do was cut off a piece that was 4.5cm wide (9HP) and spray paint it. I labeled everything with an Edding 400 marker pen.

Wirebridges and cuts. I made some minor changes to the layout after I built this so there are a few discrepancies between this picture and the current layout.

Stripboard ready for testing side A:

 

Panel, not yet labelled:

The finished module with the little 10 by 6 hole stripboard for the rate indicator LED's glued to the back of one of the potmeters. If you look closely at the sockets you can see I soldered all ground connections together with one copperwire going round them all. A wire goes from there to the ground connection on the stripboard.

The finished product:

Here's a little demo video I made showing the LFO in action in a little Eurorack setup. You can hear how the 'Pico Voice' VCO changes in sound as I connect the LFO to it. But then I get distracted by the Pico DSP effects module and the 2hp Freez, LOL. Oh well. You can hear the difference it makes anyway :)

(As you may have noticed, I really suck at making demo videos, LOL)

WAVEFORMS:

Here are some screenshots from the oscilloscope showing some of the waveforms. The one below shows the sharpest a sawtooth wave you can get. Pretty fast rise!

Cursor readings at LFO-B squarewave output:

Here is a collection of variable output readings from Variable output B:

To give you an idea of what can be achieved by mixing the two variable outputs in a simple passive multiple, here are eight images I put together to give you an impression. This should sound awesome with very slow running LFO's which is why I soldered a few more caps in parallel over the timing cap of LFO-B.

You can imagine that some of these waveforms, when put through a quantizer, would generate awesome melody- or bass-lines that can be easily manipulated with the LFO parameters. I tried to capture a little of that in the demo video I posted below.

Here's some technical data from the LFO:

LFO A: freq. range: 270mHz to 24Hz. 

LFO B: freq. range.: 41mHz (one full cycle every 24 seconds using a 650nF cap) to 2Hz.

Duty cycle of the pulsewave output goes between 2% and 98%. I made a mistake and used a 100K potmeter for the Shape but it needs a 500K potmeter. I only had one 500K pot so I put it in LFO B and the screenschots above are from that LFO. You can use a 100K for shape but that will significantly lower the range of the duty cycle (20 to 80%) also the slope of the Saw-/Rampwaves will be slower rising. It will also speed up the overall frequency of the LFO.

Maximum current draw = 20mA for both the positive and negative side.

The maximum amplitude of the waveforms is about +/-5V except for the Variable waveform output. When that potmeter is set to the mid point the output amplitude drops to about +/-2.5V because the potmeter acts as a voltage divider so in the mid position the amplitude is half of what it is when it is fully clockwise or counter clockwise. (We effectively have two 50K resistors on either side of the wiper of the 100K potmeter.) These may seem like low voltages but keep in mind that an LFO is usually attenuated anyway because if the changes are too big it just doesn't sound good on a VCO or in most patches. If you really need higher voltages you can make the 1K8 resistors on the outputs even bigger.

Here's the link to the Falstad simulation of this circuit. This is the Dual version with one speed potmeter at 100K and the other at 500K as it is in my LFO. You can change these variables by right clicking on them and choosing 'Edit':

--- CLICK HERE --- 

EXTRA FEATURE:

Okay as I write this it is four days since I posted this article and the cool looking results from the mixed variable outputs kept going through my mind. I really wanted to incorporate that into this design and now I found a way. I used an other small piece of stripboard on which I soldered a dual opamp and wired it up like the mixer in article 17 with 2 inputs. I knew there was no way to put an extra output socket on my panel so I sacrificed the squarewave output of LFO-B. That was the least useful of the outputs because I can get a squarewave anyway from the pulse output if I need one and I still have the squarewave of LFO-A. So I carefully soldered in the little mixer print which was just as big as the little LED driver and wired it all up and I re-labelled Square output B into 'Vari A+B'. I used a 200K trimmer to go over the inverting input of the second opamp and the output so I could adjust the gain and make it a little higher than the Variable outputs. I placed the little print above the sockets and used hot-glue to stick it in place. It is actually glued to the little LED driver board. This works perfectly! Now I have an output with two variable waveforms mixed together coming out of it.

Here is a picture showing how I added the mixer. I used two rigid copper wires to tap the signals from the sockets and lead them into the mixer. The non-inverting inputs of the opamps are connected to ground on the copper side:

Here's the layout of this little mixer. Mine is even smaller than this layout, but this will work fine. All resistors are 100K:

Here's the schematic for this little mixer:

DEMO VIDEO:

Finally I want to show you a little experiment I did using the new output. I put the Variable A+B signal through a quantizer (the 2hp Tune) and from there into the Pico Voice Wavetable Oscillator. The audio then went through the Pico DSP for some added reverb. You can really generate the weirdest melodies with this although this setup would benefit from the Voltage Processor because the negative phase of the signal does not produce any notes so it needs a positive offset voltage and the signal can do with some attenuation to get the notes closer together but I think you get the idea watching this short demo:

Okay, that's it for now. Article 50, wow I can hardly believe it. This journey started for me in October 2019 and I knew nothing about synthesizers then, but I was determined to get to grips with it and learn as much as possible. And what better way to learn then to build your own modular. So here we are more then 3 years and 50 projects later with a cool collection of builds helping hundreds of people to do the same. I'm really proud of what, not only I created but also of all the people who helped so much along the way with comments and directions. I'm not gonna name names but you know who you are, all of you. Thank you!! So many people told me they find the site a great help in their hobby and that's the biggest reward I could wish for. I am however going to wind down the DIY aspect of the hobby because having now built my own system and also haven gotten into Eurorack, I need to spend more time actually using it and figuring out how to use it all together. But I will remain available on Facebook and here to answer questions and help as much as I can to ensure you have a good experience using this website and get as much enjoyment out of it as I did.

PCB Version.

I recently made some Eurorack friendly PCB's for this LFO including the Variable output mixer I added on.

Here's the KiCad schematic I made for this LFO:

To get your PCB, goto the Menu and click on the top option called 'PCB Service' to find these circuitboards.

If you have any questions please put them in the comments below or post them on the special Facebook Group for this website where there are some awesome people willing to answer your questions.

Synthesizer Build part-8: 8 STEP SEQUENCER.

A simple 'Baby 8' type Sequencer made with the CD4017 chip. Easy to build and fun to use. No DIY synth should be without one of these.

EDIT: There is now a new and improved version of this sequencer available on this website. I redid the design and included some extra features like external clock input and a CV Offset control. This makes the sequencer much better to use and it is no more complicated to build than this original design. So please go over to project 49: 8 step sequencer version 2 if you want to build this 8 step sequencer.

This sequencer is one of my earlier projects and of my own design although it's more or less put together from bits of other designs like the 'Baby 8' but it works fine for me and is really easy to make and easy to tune although to build it is quite time consuming and repetitive work because a lot of steps have to be soldered eight times. I found it rather tedious work but very worth while. 

A NOTE FOR BEGINNERS: A sequencer does not actually produce any sound itself. It produces a stepped control voltage that can be routed into the CV input of a Voltage Controlled Oscillator and the VCO then produces the actual notes you hear. In a sequencer you can set each of these eight steps or notes manually (with a potmeter for each step) to any voltage/note you want.

Here's the schematic drawing for this sequencer. The connections of the rotary switch are not correct in the schematic. They must be offset by one step from those of the potmeters. So step 1 is reset by the pulse from step 2 so pin one of the switch goes to output 2 of the CD4017, pin 2 of the switch goes to output 3 of the CD4017 etc, etc.

In the schematic above the on/off switch is placed after the voltage regulator to easily switch the sequencer on or off without causing switching pulses on the voltage rails. The complete on/off switching is done with the switch of the powersupply which controls the power of your whole modular synthesizer.

Here's the stripboard layout I made for the sequencer. In the schematic I drew in switches that you can add to turn individual channels on or off but I didn't include them in my build because I didn't have the space for them on the panel. In this layout I don't use any transistors either. I thought it was nonsense to make this more difficult then it needs to be. It will work fine without them because we hardly draw any current from these outputs. The CV output signal goes straight into a VCO. The layout has an extra 10µF electrolytic capacitor on the output of the voltage regulator that is not on the schematic. It's for extra noise suppression. You can get away with using a 100nF cap or leaving it out completely.
Be careful when you wire this up, note that the jumper (or wire bridge) for output 5 is connected to pin 10 of the chip so the left bunch of jumpers skips a copper trace at output 5. Look carefully at the layout! If you want to include switches to mute individual channels then put them in series with the diode!

(Last revised: 26-Feb.-2020: Minor cosmetic changes.)

NOTE: All potmeters in the layout are shown from the front side!

Use Schottky Diodes on the wipers of the potmeters. They only have a voltage drop of 0.2V instead of the 0.6 to 0.7 Voltage drop over 1N4148 diodes usually found in sequencers like this. This means you can get deeper tones from the VCO you plug it into. Because of the 0.6 to 0.7 Volt voltage drop over the silicone diodes, the first section of the potmeters wouldn't do anything until you get above 0.6 volts. So with a lower voltage drop there's more throw on the potmeter. As an experiment I also installed a 100K potmeter over the output of the Control Voltage and the wiper goes to the CV output jack. That way you can get even lower tones although, of course, this compresses the dynamic range of the sequencer. With the potmeter fully open you get the normal range of 0.2 to 8 Volts. If you close the pot half way, your range becomes 0.1 to 4 Volts so the spacing between notes becomes smaller. You don't need to include that option, I never use it and it is not included in the layout. But anyway, this is an expirimental sequencer and as a whole it works really well, If you build it you will be happy, I guarantee it. :)
A better solution, and one you should consider if you are comfortable with designing simple circuits with opamps, is to add a DC-Offset feature to this sequencer. That way you can get the lowest notes down to 0 volt without influencing the dynamic range of the sequencer. It's easy enough to do. This is not included in the layout or schematic though.

Here's a close-up of the stripboard:

Bill of materials for the layout version. You'll need ten (10) 100K potmeters instead of the 8 mentioned in the B.O.M. below. You need one for speed control and one for offset (if you build version 2 of this sequencer which I strongly advise you to do. Go to project 49) :

Here's a picture of the sequencer:

The sequencer is build up around the CD4017 decade counter chip, using a CD40106 to create the clock pulses which also serve as the 'Gate' pulses.
The CD40106 hex inverter is used as a low frequency oscillator giving off squarewave pulses who's frequency can be controlled by the 100K potmeter. I used a 15µF electrolythic Capacitor although a 10µF will do just as well. But a little higher value will give you slower speeds so you could even try a 22µF cap. The clock pulses can be interrupted by switch S-2 to give you a chance to tune that particular channel. Sometimes it can happen that after using the 'Stop/Run' switch that the sequencer jumps to channel one. If that happens try using a different CD40106 chip. You might have a fake one and they can be quircky in their behaviour.

With S-2 closed the clock pulses go into pin 14 of the CD4017 and with every pulse the chip will output a high signal on a different pin. The order by which the different pins go high is a bit random. Here is the right order: 3,2,4,7,10,1,5,6,9,11. Because of this confusing order, the outputs are set in the right order by the wire bridges to the copper traces underneath the CD4017. From there the pulses can be accessed in the right order to avoid confusion. Following the schematic drawing, the pulses go straight into the base of the 2N2222 transistors which are used here as switches. The Base-Emitter voltage is way more than needed to saturate the transistor and fully open it up. I chose the 2N2222 transistor because it can handle a reasonably large current and there's no need to use any resistors to connect them (although using a resistor in series with the base connection wouldn't be a bad thing because we're using the 2N2222 at near the limit of the operational specs.) From this base connection we also feed the eight LED's which indicate which channel is on at each moment in time. The LED's are connected with 3K resistors to reduce current flow and still provide a bright light.
All the collectors of the transistors are connected straight to the 8 Volt power rail and the emitters are all connected to ground.
It's better to just follow the stripboard layout and skip the whole transistor setup and connect the output of the CD4017 straight to the potmeters. I'm using transistors as a sort of buffer and to make this sequencer future proof for other experiments so I can draw some current from the outputs should that be necessary. But you can just leave them out it you want to. Makes it so much easier.
By setting the different potmeters, you can create the different tonal paterns the sequencer produces.
Because the potmeters are simply used as voltage deviders, it doesn't really matter which value they are as long as it's 50K or over so that they don't draw too much current and as long as you use the same value on all 8 channels.
You can tap the 'Gate' pulses straight from pin 3 of the Speed Control potmeter to the Gate output jack mounted in the panel. The pulses are really clean looking 8 Volt squarewave pulses with a 50% duty cycle so if you use the gate output into the ADSR, it will sound as if a key is pressed every time the sequencer switches to an other note.

A ten step switch is used to select the length of the sequence. It can be anything from 1 to 8. Btw, you can easily make this a ten step sequencer by connecting the last two pins from the CD4017. I made it an 8 step because I didn't have enough space to mount everything horizontally and because 8 steps is more natural for music than 10 steps because you normally have 4 notes in a beat. So multiples of 4 are better. The potmeters on my panel are mounted vertically and I could only fit eight of them below eachother anyway.
Connect the wiper part of the switch to pin 15 of the CD4017 and the wires from 1 to 8 to their relative position on the switch. Connect pins 9 and 10 of the switch together and connect the ninth output from the CD4017 to that. The pulse going into pin 15 of the 4017 will reset the chip and the counter will start over again.
Don't forget to connect pin 13 of the CD4017 to ground.

It is best with this build to make the panel first and connect all the components and do the essential wiring while you have access. Then make the circuitboard and connect the wires to the panel. Solder the resistors straight to the LED's and the diodes to the wipers of the potmeters. Connect the cathodes together and solder a wire from there to the CV output jack.
I used 5mm LED's and I made the holes in the panel by using a drill rather than a hole enlarger bit which I normally use to enlarge the pilot holes I drilled. The drill is usually a little bit less then 5mm and therefor the LED's will sit very tight and don't even need to be glued in place (although it is best to hot-glue them in place anyway).

Do not forget to solder a big 470µF capacitor on the input of the 7808 voltage regulator. Otherwise pulses will bleed through onto the power supply rails and you'll hear the tone sequence even if the sequencer isn't connected to the CV input of the VCO. I also included an ON/OFF switch (S-1) on the panel just to have the option to shut it down. It's the only panel in my synth build to have an ON/OFF switch.

TUNING THE SEQUENCER:
To tune the sequencer, simply set it to the lowest speed and use switch S-2 to interrupt the clock pulses and stop at each channel. Then you can tune that particular channel using a tuner or simply by ear, by turning the potmeter and then you turn switch S-2 back on. The sequencer flips to the next channel, you turn it off again with S-2 and tune that note, then you flip the switch again and jump to the next channel, etc, etc. It's very simple and very effective. :)

A note for beginners. You must connect the CV OUT of the sequencer to the 1V/Oct input of a Voltage Controlled Oscillator (VCO) and the oscillator makes the actual sound. The sequencer only produces a sequence of stepped voltages that the VCO turns into notes so for tuning the sequencer you must have it connected to a VCO.

Because the sequencer can produce any voltage between 1 and 8 Volt it's difficult to set it accurately to a specific note without using a tuner. That's why most professional sequencers have a built in Quantizer which automates this proces. A Quantizer reads an incoming voltage and turns it into the nearest 1/12th of a volt, that way making sure it's a pure note. 

Because most synthesizers use the 1 volt per Octave system and there are 12 notes in an Octave, each note is produced by a multiple of 1/12th of a volt. For instance note C1 = 1.000V, note D1 = 1.083V (1 + 1/12th volt), note F3 = 3.333V (3 + 4/12th volt). So the notes progress upwards in steps of 1/12 of a volt. This sequencer does not have a quantizer and because they are quite difficult to build I don't have a quantizer project on my website. You can however buy them for Eurorack systems. In my Eurorack system I have the Doepfer A-156 QNT which costs about €119 and contains 2 quantizers.

If you are good at working with Arduino's you can easily make a quantizer with that. You can program it to turn any incoming voltage into a multiple of 1/12th of a volt.

Momentary switch:

There is a good way to include a momentary switch mentioned in the comments below by 'tamasgal'. The suggestion is to put a resistor and switch in series connected between V+ and ground and then run a resistor and capacitor from the high potential side of the switch to ground and also connect it to one of the left over schmitt-triggers of the CD40106. Then connect the output to pin 15 of the CD4017. That should take care of any bounce in the momentary switch.

In fact, I have implemented this in version 2 of this sequencer (project 49) and it works really well.

That's all there is to say about this. It's one of the most fun panels for the synthesizer but one of the most tedious to build. It cost me 6 hours straight to design and build it but luckily it worked straight away.

Here's a little demo of the sequencer. This was filmed before I put in switch S-2 so I had no option to tune the sequencer at the time of filming. I might make a new video soon:

Okay, that's another one done. I hope you enjoyed it. If you have any questions about this build then  please leave them in the comment section below or in the Facebook Group.

A 'Brute Force' 15 Amp Power (Dummy-) Load. Easy to build!

Power-loads or Dummy-loads are expensive bits of equipment but if you need to test a powersupply or test a current protection circuit and need something that can draw a big current and is preferably regulated so you can dial in the current then this is the easiest and cheapest method.

The circuit below uses a BD182 transistor which I had lying around from an old audio amplifier. It is the equivalent to the well known 2N3055 and you can exchange the one for the other in this circuit without trouble.
The powerload needs no external power supply. It is a passive circuit but do make sure you use a big, and I mean BIG, heat-sink. The transistor will get hot very quickly.
Here is the schematic drawing of the circuit. I don't think you can make them any simpler than this.

I did away with the shunt resistor in the emitter to ground line because we don't need to measure the current at that point. We will use a Digital Multimeter in series with the Dummyload input. A shunt resistor is usually used for creating a feedback voltage to go into an opamp, In this case it only holds back the current so we leave it out.
I made my dummy load switchable. You can draw a big current and then by flipping the switch the current almost doubles. The lowest resistance I got from this circuit was 1.8 Ohms. That means with 12 volts connected you can draw a little under 7 Amps. and this transistor has no troubles with that (provided the heat-sink is up to it). Be sure to use a good heat sink and generous amounts of heat conducting compound around it.

Below are some pictures of how I build my power load. I build mine in an old Droste Chocolate can I had lying around. Previously I had built it in an old wooden cigar case so this is big improvement :)
Beware that the current-rise is exponential so when you turn the potmeter, the first few amps will go nice and smooth but at the end the current rises very quickly and even jumps to maximum just before the potmeter if fully turned. And yes, the potmeter I used is a linear type not a logarithmic one :)
The current fluctuates a little if you put an amp-meter in series with the load. The milliAmp digits will go up and down a bit as you read the amperes. But that's what you get when you keep it simple. The little 50nF capacitor is meant to suppress transients should they occur.
The maximum voltage from Collector to Emitter for the BD182 is 60 Volts so don't go higher then that and the maximum continuous Collector Emitter current is 15 Amps. That's a lot more then most of the circuits for powerloads you'll find online. They mostly go up to just 5 Amps. I try not to exceed 10 Amps with this design just to be on the safe side. I used a CPU heatsink on the 2N3055 which is not ideal but I mounted the transistor on a little copper sheet so that acts as a heat sink too and then I put the CPU heatsink on top of the transistor with heat conducting paste in between so the transistor can dissipate heat from the top of the TO-3 housing aswell. It's a very effective solution and works very well. If you need a power load that can draw even more current you can just put more transistors in parallel over the first one. Just connect base to base, collector to collector and emitter to emitter. (I haven't tested that btw, but it should work.)

That's it for this article. I hope you enjoyed it. If you did then have a look around some of the other articles on my website. There's loads of interesting electronics projects, mostly synthesizer related though. Please leave me a comment, because I always enjoy hearing from likeminded people. If you'd like to support my modest efforts you can do so by subscribing to my YouTube channel EdEditz

THANK YOU!