Synthesizer Build part-49: 8 STEP SEQUENCER version 2.0

A redesigned version of the 8 step sequencer (project number 8) with external clock input option and offset control that allows you to transpose the sequence upto 3.5 octaves up or down.

-- Please read the entire article before you start building!! --

The sequencer project I posted when I was just starting out on this modular journey has rapidly become a very popular project on my website. I was however never really happy with that design. It was a bit clumsy and it had no extra features and although it worked like it should, it was never as good as I wanted it to be. It always nagged me.

So because it is such a popular project now, and using the knowledge I gained in the three years I've been building modules, I wanted to offer people something better to build. Something that I was sure wouldn't disappoint anyone building it. I'm really happy with how it turned out and I love using it. This is one of the few sequencers that can actually deliver negative voltages if you want to. Because a sequencer doesn't have to be used to make melodies or bass-lines, it can be a modulation source aswell. It really is a step above the basic baby 8 sequencers without using Arduino's. So here it is; the 8 Step Sequencer version 2.0 

A NOTE FOR BEGINNERS: A sequencer does not actually produce any sound itself. It produces a stepped control voltage that can be patched into the CV input of a Voltage Controlled Oscillator and the VCO then produces the actual notes you hear. In a sequencer you can set each of these (8) steps manually to any voltage (and therefore any note) you want within 1 to 5 octaves.

This sequencer has a few advantages over the first one. 

01 External Clocking. The sequencer can be clocked by an external source. In order to make sure this external clocking would work as well as possible I decided to use some of the hex inverters with Schmitt-Trigger inputs in the CD40106 chip (that we use to provide the internal clock signal) as buffers. A Schmitt-Trigger input has hysteresis. This means there's a voltage difference between when the hex inverter flips from on to off. For instance it might jump to off when the input goes over 6 Volt and turn on when the input gets below 4 Volt (remember it's an inverter). That's a 2 Volt hysteresis and this means it will be less susceptible to noise on the external clock signal. This turned out to work just like I hoped it did. I used two of these inverters switched in series so the (external) clock pulse itself is not inverted. I did a test and installed a bypass switch to feed the signal past the two hex inverters and immediately the external clocking stopped working for some signals, proving it's a good solution.

There is one little downside. The external clockpulse needs to be quite high in voltage. A 5 Volt pulse won't be enough. It should preferably be 6V or higher. I tried clocking it with the Behringer RD-8 but it wouldn't work. But when the pulse is high enough in voltage it won't matter what wave shape you use, it'll work.  The Yusynth LFO with sync and FM input was able to trigger it if I used the triangle wave as external trigger. 

NB: One option to solve this problem: You can lead the trigger pulse through the Voltage Processor first and give it a little positive offset voltage. That way it will breach the 6V minimum threshold. 

An other option would be to use an opamp as a comparator so that if the trigger rises above a certain threshold the opamp goes high and low again when the signal trigger goes below the threshold. I found a comparator design that works. You could put this on a tiny piece of stripboard and solder it to the input lug of the external trigger input socket and connect it to the external clock input. I would use a toggle switch to go between internal and external clock in this case. Btw, I have now tested this design and it works provided you connect the 741 chip to positive and negative 12 V as shown in the layout.

The clockpulse will come out with a 180° phase shift but it will be a 0 to +10V pulse.

I used this design for the clock input of the PCB version of this sequencer and it works great. It takes any waveform and changes it into a useable clock pulse. 

I took this design from the input of the Waveshaper project. You can find the schematic in project 60.

I took some pictures of the input (in blue) and output (in yellow) from the scope screen. In the first picture I used a squarewave going in and in the second a triangle wave. As you can see they are both converted into a nice 0-10Vpp clock pulse:

02 CV OffSet. This sequencer has an Offset feature. That means you can transpose the whole CV output chain up or down by as much as 3.5 octaves without compromising the Volt per Octave tracking. With the previous sequencer we were limited in the lowest notes by the voltage drop of the diodes on the potmeters. So it was never possible to get to note C0 which is 0.0833 Volt. But now we can trim the offset down and that will drag the whole sequence down in voltage making it possible to get to the lowest possible notes without screwing up the volt/oct. tracking and without need for special Schottky Diodes. I did use Schottky diodes (which have a voltage drop of only 0.2V) but only because I re-used the old sequencer for this build and the diodes were already soldered to the potmeters.

The offset feature is a game changer for this sequencer in my opinion because we can make really cool basslines or melodies and transpose it up or down without any problems. Naturally the output is not quantized so you won't land on true notes every time when tuning or transposing the sequencer. It's always a good idea to have a quantizer in your rig but they are too complicated for me to build as a DIY project. However, you can buy a eurorack quantizer like the Doepfer A-156 QNT (which I have in my Eurorack system) for €119,- (and that's a dual quantizer with extra options!) On the other hand, without a quantizer we can tune by ear and to what sounds right to us, without being bound by set scales. So there are advantages too to not having a quantizer. I always tune my sequencer with the Joyo tuner which I hacked for modular use (click here for that project.)

The offset feature can also be very useful if you use the sequencer as a modulation source for instance to modulate the filter. You can drag the sequence down so some steps have a negative voltage and others a positive voltage and so create weird VCF responses. 

For those of you interested, the CV voltage (the sequence) goes into the inverting input of the offset opamp and the offset voltage goes into the non inverting input. Then in the second opamp the CV voltage is inverted back to normal again while the offset voltage now gets inverted. That's why the wiring of the offset potmeter is the other way around from normal. The output opamp has a 470pF capacitor over the feedback resistor to suppress little voltage spikes which I could see on my oscilloscope, just like in the Sample and Hold v2.0 project. The 470pF gets rid of that very effectively.

03 External Speed Control. I recently added an external speed control so you can influence the speed of the sequencer with an LFO or ADSR or any other CV source while still being able to set the overall speed with the speed control on the panel. I did this by simply putting a Vactrol over the Speed potmeter. It's really easy to do. Just add an extra input socket and make a Vactrol and connect the LED of the Vactrol to the socket using a 1K current limiting resistor to protect the LED in the Vactrol. Make sure you connect the plus to the audio lug of the socket and not the ground one. Also make sure you test the Vactrol before putting it in. My own Vactrol died on me a few days later but I used a 470 Ohm resistor instead of a 1K and that is too small as a current limiting resistor. Use 1K and a bright white LED. That should work fine for CV voltages upto +10V.

I did not add an attenuator for this function because I ran out of space on the face plate but you could of course do that if you wanted to. Vactrols consist of a Light Emitting Diode (LED) and a Light Dependent Resistor (LDR) wrapped together in some Heat-Shrink Tubing. They are really easy to make. There are enough videos on YouTube that show you how to make them. You can of course also buy them new. Now Vactrols are not very accurate in how they work so you can't set the speed exactly to a certain value with a certain voltage. This feature is meant to influence the sequencer in a musical way, like speed it up every x number of beats, to create some variation.

An other way to vary the sequencer speed is to vary the external clock speed when using an external clock. This would be a more exact option if, for instance, you are clocking the sequencer with an LFO with an external Frequency Modulation input, like the LFO in project 30.

Please only add the external speed control if you think you'll need it, otherwise save yourself the trouble.

SPEED CONTROL and the TUNE/RUN switch.

The sequencer has a speed control potmeter that will go from 1.34 seconds (746mHz) to about 185Hz. If you want that speed to be lower you can add a 4,7µF cap in parallel over the 10µF cap to bring that speed down to about 2 seconds which is slow enough and it will still be able to go very fast too. 

It also has the tune/run feature of the previous sequencer to make tuning each step easier. The old procedure was to just set the speed very slow and then stop the sequencer at each step so you could tune it. Then you would switch to Run to go to the next step and stop it again to tune that one. With this new version you can use the push switch to manually go through the steps to tune them.

I had some problems with stopping the sequencer in the beginning. The sequencer would continue running even after switching it to Tune but the solution was simple. When switched to Tune the clock input must be grounded (which I hadn't done). I used a 1K resistor for that, connected to the switch and to ground. This is why it is important to connect the wire that is in direct contact with pin 14 of the CD4017 to the middle pin of the Run/Tune switch. Otherwise this doesn't work. 

A word about tuning: it's not the easiest thing to tune this sequencer to an exact note due to the fact we have 7 Volt to deal with and a 100K potmeter to set it to an exact note. In the 1V/Octave standard the difference between two notes is only 0,1666 Volt. And between two half notes only 83,3 thousandth of a Volt. That sort of resolution is difficult to achieve with a normal potmeter. However it is not impossible. It takes little touches of the potmeter but, as you can see in the demo videos below, it can easily be done with a little patience and accuracy. This problem goes for all Baby 8 sequencers, not just this one and I use mine a lot and I've always managed to get it sounding really good and in tune. This is also why the CD4017 is powered with 8 Volt. If you gave it 12V the resolution would be much worse.  As I mentioned earlier, you could buy a cheap eurorack quantizer which would help a lot with accurate tuning but that's up to you. Or, an other really helpful tool to have is the Joyo Tuner, hacked for use with modular synthesizers. It's what I personally use to tune my sequencer.

MOMENTARY SWITCH

I had a lot of problems in the beginning, implementing a momentary switch into this design. With that switch you can advance one step each time you push it to switch between channels to make tuning easier. The problem was that I forgot to ground the clock input of the CD4017 when the sequencer is in Tune mode. I made some changes and I connected a 1K resistor to the 'Run/Tune' switch that grounds the clock input. After I had done that I thought I'd try to get the momentary switch working. I connected a momentary switch between +8V and the pin of the 'Run/Tune' switch that has the 1K resistor connected to it. But when I switched to Tune mode it still kept jumping several steps when I pushed the switch. I figured this must be due to contact bounce in the switch. To counter that I soldered a 100nF capacitor in parallel over the momentary switch and that did the trick. Now it works like it should. It's not perfect. Occasionally it will still skip a step randomly but that happens very rarely. Overall it works really well and it's perfectly useable. You can put in a bigger value capacitor like a 470nF if you want to be sure it works perfectly. (The PCB version uses 470nF)

SCHEMATIC:

Here is the schematic for this sequencer. I made it using Photoshop. 

I have only drawn two of the output steps coming out of the CD4017, with the LED, the potmeter and the diode connecting to the CV Rails. You need 8 of those to complete the 8 steps of the sequencer of course. The CV Rails is just a bare copper wire where the outputs of each of the 8 steps are soldered to. From there a wire then connects the CV Rails to the offset opamp on the stripboard.

The addition of the offset feature means that when the sequencer is switched off, there would normally still be an offset voltage on the CV output! I have routed the CV output through the same switch as the one we use to switch the sequencer on and off. So when we switch the sequencer off the CV output is also interrupted. That's why we need a dual pole switch for the on/off.

ALTERNATIVE SPEED CONTROL:

I found a better way to do the speed control on the sequencer. Instead of just a 100K pot and a 10µF cap, use a 500K potmeter with a 10K resistor in series and then use a 4,7µF cap like in the picture below:

This gives a better and smoother speed control. This is not implemented on the stripboard layout so you'll have to make these changes yourself.

The connections of the rotary switch follow one step behind the connections of the potmeters. So step 1 is reset by the pulse from step 2 so be very accurate in that. I got that wrong in the previous version. 

There are two diagrams on the layout below explaining where all connections go for the potmeters and for the rotary switch.

In the schematic I use normal 1N4148 diodes but in the layout they are named as 1N5819 Schottky diodes. Go with the 1N4148 diodes. I only have Schottky's in the layout because that's what was already in there from the previous version of this sequencer. Schottky diodes have a lower voltage drop than normal silicone diodes but now that we have the Offset feature the voltage drop is no longer an issue.

It is totally unnecessary to include transistors in the output steps to feed the LEDs. I just put 10K resistors in series with the LEDs to keep their current draw to a minimum and because opamps don't draw any current at all the LEDs do not pull down the voltage when they are on. The LEDs are fed with 8V from the outputs of the CD4017 and with the 10K resistors they are still bright enough. It is however important that you do NOT use any LEDs that draw a lot of current like blue LEDs or bright white LEDs. Those may draw the voltage of the CV output down. Not only that, in the long run they can heat up the CD4017 so much that it fails. The outputs from the chip can't deliver more than 6.8mA maximum with a 15V power supply. (see datasheet)

(The PCB version runs on +/-12V and uses a 7805 to feed the CD4017 and the potmeters (5 octaves) and it has 4K7 resistors on the LEDs.)

The current draw of this module is incredibly low. The +12V part only draws 6 mA in normal use and with the internal clock at full speed it draws 10 mA. The negative side, -12V, only draws 0.73 mA! That's 730 µA! Regardless of the clock-speed. That's nothing! So you can easily run this module on two 9V batteries and use it as a stand alone sequencer should you wish to do so, and your batteries will last for months. (use 2 batteries to create a dual voltage supply)

The Gate output produces gate signals that are exactly half the length of a single CV step. In other words they have a duty cycle of 50%.

HERE IS A FALSTAD SIMULATION OF THIS CIRCUIT: --- CLICK HERE ---

LAYOUTS:

Below is the layout I made for this project. If you built the first version of this sequencer earlier, then it's really easy to replace just the stripboard with this new one. You only have to make two extra holes in the face plate for the external clock input socket and for the External Speed CV input (or three if you want to include the 'end of cycle' trigger output) and all you have to do is reconnect the old wiring to the new stripboard,

In this layout I connected only the first 3 steps to show you how it should be done. You can easily repeat these connections for the other 5 steps. I did this to prevent the layout becoming a mess of hook-up wires. Follow the numbering in the text at the bottom right to connect the potmeters and rotary switch pins to the correct pins of the CD4017. Of course you could include the left over two pins from the chip to make it a 10 step sequencer but 10 steps don't sound right. Normally you got 4 steps to a beat so 8 steps sounds better. If you do want to make it a 10 step sequencer you will need a rotary switch with 11 positions! Otherwise, if you use a 10 step switch, the CD4017 will be reset at step 9 instead of 10. In case of a 10 step sequencer you don't need a reset pulse because the CD4017 only goes to 10 steps so it will reset itself.

This sequencer is equipped with an ON/OFF switch so you can easily introduce it into a jam session by flicking the switch. That way you can leave it patched up and have it instantly available when you need it. The ON/OFF switch for this module is located behind the voltage regulator and that is done on purpose. If you put it before the regulator the sequencer would shut down very slowly because the 470µF capacitor discharges very slowly. So you would hear the sequence getting slower and slower and the notes going out of tune and fading out if you switched off. With the switch behind the voltage regulator the switch-off (or on) is instantly done. The regulator itself doesn't use any current when not in use and this has the added bonus that the sequencer starts up immediately too if you switch it on.

If you want to include 'Mute' switches for each step then I indicated on the layout the best place to put them (after the diode of each step). If you mute a step there will still be a gate signal for that step present on the Gate output.  

Wiring diagram:

If you don't want to include the External Speed control, just leave it out. 

I show only 3 of the 8 steps in this layout to avoid it becoming too cluttered with hook-up wires. It's already a mess of wires. Just repeat the LED, Diode and Potmeter combinations five more times. The list at the bottom right tells you where to connect each step. This layout also contains an LED pinout diagram.

All potmeters are viewed from the front!

(The connections of the rotary switch follow one step behind the connections of the potmeters to the CD4017. That's why there are two columns of connections on the lower right.)

Please be aware of the wiring of switch 1a and 1b. The switch interrupts power to the CD40106 and CD4017 chip and also the CV output.

THE LAYOUT BELOW IS THE SAME LAYOUT AS ABOVE ONLY THE POTMETERS ARE NOW SEEN FROM THE BACKSIDE! I thought this might be helpful for some people when wiring up the panel.

NOTE: The position of the Gate output wire as I built it here will mean that when you set the sequencer to 'Tune' you won't get a gate signal output if you push the momentary switch. If you do want a gate output when in tune mode then de-solder the wire that goes to the gate output socket out from the stripboard and solder it to the middle pin of the 'RUN/TUNE' switch or to the right hand side of strip L (pos. 22 to 38). That way you'll always have a gate signal when the sequencer moves from one step to the next. I don't think it's necessary to make this change but I just want to mention it here.

Wiring procedure:

When you are ready with the stripboard and ready for wiring, make the face plate first and put all the potmeters, sockets. LEDs and switches in. Then wire up the potmeters with the diodes to the CV rail (a bare copper wire) that connects with a wire to the stripboard. Wire up all the LEDs too. Now loosely connect the stripboard to the faceplate and then you can wire everything up to the stripboard very easily.

The mysterious grey component at the bottom middle is an L-Bracket to mount the stripboard to the faceplate. But you can use any method you want to connect the stripboard to the faceplate. In my build the stripboard is mounted parallel to the faceplate with one M3 threaded stand-off. The wiring also helps to keep it in place nicely.

TIP: You could connect a socket to each of the 8 stages (before the potmeter) and so use this as a trigger sequencer too.

Stripboard only view:

Below is a close-up of the stripboard. The voltage regulator and the big 470µF electrolytic capacitor plus the other two 10µF caps are quite crammed in together on the top left of the board but it shouldn't be a problem. The voltage regulator doesn't even get warm in normal use so it doesn't need a heatsink. You could also use the smaller 78L08 types that look like a TO-92 package transistor. 

You do need the big 470µF cap in there otherwise the pulsetrain could be audible on the voltage rail. In fact, I myself used a 2200µF/16V cap in that position to be on the safe side. (The light blue edges of the caps indicate the negative pole.)

Cuts and Wirebridges:

Below are the cuts and wirebridges seen from the component side. As always, mark the cuts on the component side first using this layout and then stick a pin through the marked holes and mark them again on the copper side and cut the strips by hand with a sharp 6 or 7mm drill bit. That way you have the least chance of making mistakes. Check the cuts afterwards with the continuïty mode of your digital multimeter or a strong magnifying glass.

Bill of materials.  This is a new version including a Vactrol for the external speed option.

In my own sequencer I actually have two Gate Out sockets, just connected together. I found it useful in some patches to have two so order 5 sockets it you want to include that option.

Pictures:

Here are some pictures of the stripboard during the building proces. My stripboard had one little error in it which was spotted by one of our awesome Facebook members and that was that the copper strip connecting pin 8 of the CD4017 to ground had a cut in it. I built it with that error included and strangely enough it worked normally but I have now corrected it. I made an other error in the top picture, the connection to +12V for the TL072 chip has been forgotten. (Holes N-41 and O-41 in the picture below) You can see it's added in the picture below it:

OSCILLOSCOPE SCREENSHOTS:

Here's a picture of the 'End of Cycle' trigger pulse that resets the CD4017. You can see how enormously fast this pulse rises and falls, within 280 nanoSeconds. (Ignore the yellow line above it.) 

In itself it's not too strong a signal so the signal is routed through two of the left over Schmitt Trigger inverters of the CD40106. This makes sure we'll get a strong 8V end of cycle pulse output. 

Here's an example of a CV output sequence with potmeters set to various notes.  As you can see the maximum output voltage is around 7 Volt (or 7 octaves) when the potmeter(s) are fully set clockwise and goes all the way to 0V with the potmeter(s) fully closed and a little negative offset applied. You can easily set or adjust this just by ear. 

And this is a scope image of the clock pulse generated by the CD40106 as it enters the CD4017:

DEMO VIDEOS:

Finally, here's a little demo video showing the sequencer in action connected to a Thomas Henry VCO-555 and the Steiner Parker filter.

If you can't see the video above, here's the link:  https://youtu.be/lcsw4txNoj 

And here's a video of me trying to replicate the intro from Vangelis' Spiral. I always loved that sequence. The sequencer is again connected to a Thomas Henry 555-VCO and the Steiner Parker filter. Plus a little echo from the FX Unit:

To get this sound connect the sequencer CV out to the Exp. FM Input of the Thomas Henry VCO-555 (attenuator fully clockwise). Take the Sawtooth output and patch it to the input of the Steiner-Parker filter set to Lowpass. From there into the VCA and add some echo with preset 59 of the CaraOK FX Unit. Just add a little of the echo. Play with the VCF Cut-off to get the variation in the sound.

To program that pattern, tune your steps as follows:  F2, C2, F3, C3, F4, C4, F5, C5

And finally a test with Vangelis' Dervish-D intro. Make sure you use a fast envelope on the VCA because the notes need to sound punchy.

The note progression for this sequence is: C#3, C#3, C#4, G#3, B3, G#3, F#3, E3

CLOCKING AT AUDIO RATES or the SEQUENCER as WAVEFORM GENERATOR:

I was watching one of Sam Battle's (LMNC) videos and he talked about using a Baby 8 sequencer as a waveform generator. If you clock this sequencer at audio rates you will in fact get an other oscillator with a waveform that is cut into 8 steps (or less) and adjusting each step will change that part of the waveform and with it the overall sound of the oscillator/sequencer. The sequencer is clocked by a VCO so the clock frequency will change with the note you play so it will track over the octaves and the CV out from the sequencer can go straight into a filter.

It's a really fun thing to experiment with. I'll link to the video in question below here, where Sam explains how this works. The video should start at 9:25:

https://youtu.be/wmqCtuT1PDE?si=yxJVTJrG-m7D-4QJ&t=565

KORG SQ-1

TIP: Finally here's a little tip for all you who want to take sequencing a little further. Buy a Korg SQ-1 sequencer. It costs less than €100,- and will give you 16 steps or 2x8 steps and a miriad of options. This is of course not a module but a stand alone sequencer but it is very small and runs on 2 AA batteries. The case is made of metal and the thing weighs over a kilo! It outputs quantized CV voltages and you can set the voltage range to upto 8V. A lot of performers use an SQ-1 in their live sets. It also works very well with the modular synthesizer I've built from all these projects.

If you want to know more about this easy to use sequencer then just Google "Korg SQ1" or even better do a search on YouTube and you will find a sea of videos on this machine that will tell you all you want to know. 

Okay that's it for the Sequencer V2.0. As always, if you have any questions or remarks about this or other projects please comment below or post on the Facebook Group for this website.

Synthesizer Build part-8: 8 STEP SEQUENCER.

A simple 'Baby 8' type Sequencer made with the CD4017 chip. Easy to build and fun to use. No DIY synth should be without one of these.

EDIT: There is now a new and improved version of this sequencer available on this website. I redid the design and included some extra features like external clock input and a CV Offset control. This makes the sequencer much better to use and it is no more complicated to build than this original design. So please go over to project 49: 8 step sequencer version 2 if you want to build this 8 step sequencer.

This sequencer is one of my earlier projects and of my own design although it's more or less put together from bits of other designs like the 'Baby 8' but it works fine for me and is really easy to make and easy to tune although to build it is quite time consuming and repetitive work because a lot of steps have to be soldered eight times. I found it rather tedious work but very worth while. 

A NOTE FOR BEGINNERS: A sequencer does not actually produce any sound itself. It produces a stepped control voltage that can be routed into the CV input of a Voltage Controlled Oscillator and the VCO then produces the actual notes you hear. In a sequencer you can set each of these eight steps or notes manually (with a potmeter for each step) to any voltage/note you want.

Here's the schematic drawing for this sequencer. The connections of the rotary switch are not correct in the schematic. They must be offset by one step from those of the potmeters. So step 1 is reset by the pulse from step 2 so pin one of the switch goes to output 2 of the CD4017, pin 2 of the switch goes to output 3 of the CD4017 etc, etc.

In the schematic above the on/off switch is placed after the voltage regulator to easily switch the sequencer on or off without causing switching pulses on the voltage rails. The complete on/off switching is done with the switch of the powersupply which controls the power of your whole modular synthesizer.

Here's the stripboard layout I made for the sequencer. In the schematic I drew in switches that you can add to turn individual channels on or off but I didn't include them in my build because I didn't have the space for them on the panel. In this layout I don't use any transistors either. I thought it was nonsense to make this more difficult then it needs to be. It will work fine without them because we hardly draw any current from these outputs. The CV output signal goes straight into a VCO. The layout has an extra 10µF electrolytic capacitor on the output of the voltage regulator that is not on the schematic. It's for extra noise suppression. You can get away with using a 100nF cap or leaving it out completely.
Be careful when you wire this up, note that the jumper (or wire bridge) for output 5 is connected to pin 10 of the chip so the left bunch of jumpers skips a copper trace at output 5. Look carefully at the layout! If you want to include switches to mute individual channels then put them in series with the diode!

(Last revised: 26-Feb.-2020: Minor cosmetic changes.)

NOTE: All potmeters in the layout are shown from the front side!

Use Schottky Diodes on the wipers of the potmeters. They only have a voltage drop of 0.2V instead of the 0.6 to 0.7 Voltage drop over 1N4148 diodes usually found in sequencers like this. This means you can get deeper tones from the VCO you plug it into. Because of the 0.6 to 0.7 Volt voltage drop over the silicone diodes, the first section of the potmeters wouldn't do anything until you get above 0.6 volts. So with a lower voltage drop there's more throw on the potmeter. As an experiment I also installed a 100K potmeter over the output of the Control Voltage and the wiper goes to the CV output jack. That way you can get even lower tones although, of course, this compresses the dynamic range of the sequencer. With the potmeter fully open you get the normal range of 0.2 to 8 Volts. If you close the pot half way, your range becomes 0.1 to 4 Volts so the spacing between notes becomes smaller. You don't need to include that option, I never use it and it is not included in the layout. But anyway, this is an expirimental sequencer and as a whole it works really well, If you build it you will be happy, I guarantee it. :)
A better solution, and one you should consider if you are comfortable with designing simple circuits with opamps, is to add a DC-Offset feature to this sequencer. That way you can get the lowest notes down to 0 volt without influencing the dynamic range of the sequencer. It's easy enough to do. This is not included in the layout or schematic though.

Here's a close-up of the stripboard:

Bill of materials for the layout version. You'll need ten (10) 100K potmeters instead of the 8 mentioned in the B.O.M. below. You need one for speed control and one for offset (if you build version 2 of this sequencer which I strongly advise you to do. Go to project 49) :

Here's a picture of the sequencer:

The sequencer is build up around the CD4017 decade counter chip, using a CD40106 to create the clock pulses which also serve as the 'Gate' pulses.
The CD40106 hex inverter is used as a low frequency oscillator giving off squarewave pulses who's frequency can be controlled by the 100K potmeter. I used a 15µF electrolythic Capacitor although a 10µF will do just as well. But a little higher value will give you slower speeds so you could even try a 22µF cap. The clock pulses can be interrupted by switch S-2 to give you a chance to tune that particular channel. Sometimes it can happen that after using the 'Stop/Run' switch that the sequencer jumps to channel one. If that happens try using a different CD40106 chip. You might have a fake one and they can be quircky in their behaviour.

With S-2 closed the clock pulses go into pin 14 of the CD4017 and with every pulse the chip will output a high signal on a different pin. The order by which the different pins go high is a bit random. Here is the right order: 3,2,4,7,10,1,5,6,9,11. Because of this confusing order, the outputs are set in the right order by the wire bridges to the copper traces underneath the CD4017. From there the pulses can be accessed in the right order to avoid confusion. Following the schematic drawing, the pulses go straight into the base of the 2N2222 transistors which are used here as switches. The Base-Emitter voltage is way more than needed to saturate the transistor and fully open it up. I chose the 2N2222 transistor because it can handle a reasonably large current and there's no need to use any resistors to connect them (although using a resistor in series with the base connection wouldn't be a bad thing because we're using the 2N2222 at near the limit of the operational specs.) From this base connection we also feed the eight LED's which indicate which channel is on at each moment in time. The LED's are connected with 3K resistors to reduce current flow and still provide a bright light.
All the collectors of the transistors are connected straight to the 8 Volt power rail and the emitters are all connected to ground.
It's better to just follow the stripboard layout and skip the whole transistor setup and connect the output of the CD4017 straight to the potmeters. I'm using transistors as a sort of buffer and to make this sequencer future proof for other experiments so I can draw some current from the outputs should that be necessary. But you can just leave them out it you want to. Makes it so much easier.
By setting the different potmeters, you can create the different tonal paterns the sequencer produces.
Because the potmeters are simply used as voltage deviders, it doesn't really matter which value they are as long as it's 50K or over so that they don't draw too much current and as long as you use the same value on all 8 channels.
You can tap the 'Gate' pulses straight from pin 3 of the Speed Control potmeter to the Gate output jack mounted in the panel. The pulses are really clean looking 8 Volt squarewave pulses with a 50% duty cycle so if you use the gate output into the ADSR, it will sound as if a key is pressed every time the sequencer switches to an other note.

A ten step switch is used to select the length of the sequence. It can be anything from 1 to 8. Btw, you can easily make this a ten step sequencer by connecting the last two pins from the CD4017. I made it an 8 step because I didn't have enough space to mount everything horizontally and because 8 steps is more natural for music than 10 steps because you normally have 4 notes in a beat. So multiples of 4 are better. The potmeters on my panel are mounted vertically and I could only fit eight of them below eachother anyway.
Connect the wiper part of the switch to pin 15 of the CD4017 and the wires from 1 to 8 to their relative position on the switch. Connect pins 9 and 10 of the switch together and connect the ninth output from the CD4017 to that. The pulse going into pin 15 of the 4017 will reset the chip and the counter will start over again.
Don't forget to connect pin 13 of the CD4017 to ground.

It is best with this build to make the panel first and connect all the components and do the essential wiring while you have access. Then make the circuitboard and connect the wires to the panel. Solder the resistors straight to the LED's and the diodes to the wipers of the potmeters. Connect the cathodes together and solder a wire from there to the CV output jack.
I used 5mm LED's and I made the holes in the panel by using a drill rather than a hole enlarger bit which I normally use to enlarge the pilot holes I drilled. The drill is usually a little bit less then 5mm and therefor the LED's will sit very tight and don't even need to be glued in place (although it is best to hot-glue them in place anyway).

Do not forget to solder a big 470µF capacitor on the input of the 7808 voltage regulator. Otherwise pulses will bleed through onto the power supply rails and you'll hear the tone sequence even if the sequencer isn't connected to the CV input of the VCO. I also included an ON/OFF switch (S-1) on the panel just to have the option to shut it down. It's the only panel in my synth build to have an ON/OFF switch.

TUNING THE SEQUENCER:
To tune the sequencer, simply set it to the lowest speed and use switch S-2 to interrupt the clock pulses and stop at each channel. Then you can tune that particular channel using a tuner or simply by ear, by turning the potmeter and then you turn switch S-2 back on. The sequencer flips to the next channel, you turn it off again with S-2 and tune that note, then you flip the switch again and jump to the next channel, etc, etc. It's very simple and very effective. :)

A note for beginners. You must connect the CV OUT of the sequencer to the 1V/Oct input of a Voltage Controlled Oscillator (VCO) and the oscillator makes the actual sound. The sequencer only produces a sequence of stepped voltages that the VCO turns into notes so for tuning the sequencer you must have it connected to a VCO.

Because the sequencer can produce any voltage between 1 and 8 Volt it's difficult to set it accurately to a specific note without using a tuner. That's why most professional sequencers have a built in Quantizer which automates this proces. A Quantizer reads an incoming voltage and turns it into the nearest 1/12th of a volt, that way making sure it's a pure note. 

Because most synthesizers use the 1 volt per Octave system and there are 12 notes in an Octave, each note is produced by a multiple of 1/12th of a volt. For instance note C1 = 1.000V, note D1 = 1.083V (1 + 1/12th volt), note F3 = 3.333V (3 + 4/12th volt). So the notes progress upwards in steps of 1/12 of a volt. This sequencer does not have a quantizer and because they are quite difficult to build I don't have a quantizer project on my website. You can however buy them for Eurorack systems. In my Eurorack system I have the Doepfer A-156 QNT which costs about €119 and contains 2 quantizers.

If you are good at working with Arduino's you can easily make a quantizer with that. You can program it to turn any incoming voltage into a multiple of 1/12th of a volt.

Momentary switch:

There is a good way to include a momentary switch mentioned in the comments below by 'tamasgal'. The suggestion is to put a resistor and switch in series connected between V+ and ground and then run a resistor and capacitor from the high potential side of the switch to ground and also connect it to one of the left over schmitt-triggers of the CD40106. Then connect the output to pin 15 of the CD4017. That should take care of any bounce in the momentary switch.

In fact, I have implemented this in version 2 of this sequencer (project 49) and it works really well.

That's all there is to say about this. It's one of the most fun panels for the synthesizer but one of the most tedious to build. It cost me 6 hours straight to design and build it but luckily it worked straight away.

Here's a little demo of the sequencer. This was filmed before I put in switch S-2 so I had no option to tune the sequencer at the time of filming. I might make a new video soon:

Okay, that's another one done. I hope you enjoyed it. If you have any questions about this build then  please leave them in the comment section below or in the Facebook Group.