Synthesizer Build part-69: FEATURE RICH SUB-OSCILLATOR.

A feature rich sub-oscillator taken from the Thomas Henry VCO Maximus. It has -1,-1.5, -2,-3 octaves, octaves or fiths (interval), polarity setting and a blend option with the original pulse wave.

Finally a new stripboard project and this is a good one too. I never featured a sub-oscillator design on my website before but I was looking for a good design which I wanted to combine with the X4046 VCO to build my version of the ultimate analog VCO for eurorack on PCB.

So I found this design on the Birth of a Synth website, a website that provided many projects already, and I needed to test it before I could add it to the 4046 vco so I made a stripboard layout for it and it worked great. 

This sub oscillator comes from the VCO Maximus design which is a 3340 VCO like the digisound-80 from project 18 and that means the squarewave output is at 0V to +10V instead of +/-5V like the 4046 and the sub-oscillator does not work with a bi-polar signal on the input so I added an offset feature so you can trim the input wave to be unipolar and therefore this suboscillator as presented here will work with both uni-polar and bi-polar signals on the input. 

SCHEMATIC:

Here's the schematic I used for this project:

In this schematic I drew in the offset feature though the IC numbering is different from the layout.

Capacitor C3 is very necessary. It ensures the incoming pulse signal doesn't overwhelm the flip-flops which would result in tiny spikes in the signal which would disrupt the working of the sub oscillator.

This suboscillator consists of a number of exclusive OR gates in the CD4070 and two flip-flops in the CD4013 for octave switching. You can set the octaves between -1 and -2, you can set the polarity of the signal between positive and negative. It allows you to add or subtract the subdivided pulse from the original. The different sub division options through the switch settings can give a divide by 1.5, 2, 3 or even 6. I urge you to read the original Birth of a synth article I linked to above for more information on that. It's very informative.

LAYOUTS:

Here are the layouts I made for this project. As always they are verified, I used them for my tests.

Wiring diagram:

Stripboard only:

Cuts and wirebridges:

There are 31 wirebridges to put in and that's why it takes up a lot of space dispite this being a project with very few components.

 

Bill of Materials:

Make sure you get your logic chips from a reputable source. There are a lot of fakes on the market and this design might not work well when you use those.

OSCILLOSCOPE SCREENSHOTS:

Here are some of the test results from the oscilloscope. They look amazing and show that this is not your average sub oscillator but quite a cool addition to any VCO. It's easy enough to make this as a stand alone module so you can plug any VCO into it. The Blue wave is the input wave.

Divided by 3:

Blend potmeter half open:

Polarity lets you add or subtrackt the subdivided signal from the original pulse:

In the next 3 pictures you see what happens when the blend potmeter is used. The middle bits of the waves move past eachother. The top one moves down and the bottom one moves up until they form one squarewave again. That sounds really cool. Unfortunately there's no CV control for the Blend feature but it wouldn't be too difficult to put a Vactrol over it so it's not impossible.

Below a picture of my stripboard build. Because I only built this to test how it works and see if it would be compatible with other VCO's, I did not make a panel for it so this is as far as I got with this project. Well worth the effort. It's a great suboscillator and would make a great stand-alone module.

And that's really all there is to this article. It's short but sweet. I'm going to use this design in my upcoming PCB build which I'm calling the X4046 super VCO. It'll be a 16hp eurorack module with 3 PCB's mounted behind eachother using pinheaders. I really look forward to building it. I've been working on the design for a few weeks now, I keep refining it.

I hope you enjoy building this project. If you have any questions please leave them in the comments below or on the special Facebook Group for this website.

If you like this content and would like to support my efforts and the upkeep of the website you can find a donation button underneath the main menu or you can use this link to cut out the middle man. Thank you very much!!