Showing posts with label sequential. Show all posts
Showing posts with label sequential. Show all posts

Wednesday, 4 December 2019

Synthesizer Build part-6: THE SEQUENTIAL PRO ONE LOWPASS FILTER.

The first filter I built and not one of the best in my opinion. Skip to an other project. I'm keeping this up for archival purposes.

[EDIT] Before we start: I'm writing this about 7 months after I published the article below and I can tell you now that I removed this filter from my synth. I couldn't get it to self-oscillate and I was not impressed with the sound of it. Maybe that's due to the fact that I was just starting out with synth building when I made this and I made some mistakes, but if you have the AS3320 chip I advise you to use it for the Digisound 80.6 lowpass filter. That is an amazing sounding filter!
I'm keeping this article up because this website is an archive of all my builds and that includes the ones that were not a succes (That's only this project anyway. The rest all works fine.)

Okay on with the original text:

I've considered many filter designs, and there's a lot to choose from if you search for schematics on the internet, but I've picked out 3 filters that I want in my synthesizer. Two of those are LowPass filters and one has the choise between Lowpass and Highpass. That's the Korg MS20 filter We'll get to that one later.

Now we will concern outselves with the Sequential Circuits Pro One (and many others) Lowpass filter based on the AS3320 chip. I went to the ElectricDruide website and found a page full of filters and amongst them I found this circuit:



There are also versions which are re-configurable with the flick of a switch but they were a bit too complicated for my taste and I thought this would be a great project to start with. Well, it was a good project to learn from but the result was nothing to write home about.

I made a layout on stripboard which you can find in the picture below. All potmeters viewed from the front.:


(Layout revised 15-Feb-2021)

Print only:

Bill of Materials:


The first version I made of this had capacitors that were 220pF instead of the 150pF as seen in this schematic. I thought that would give me more control over the low frequencies and I was right, LOL! It brought the top cut-off frequency down to about 200Hz. Way too low. So I soldered in the 150pF and everything worked after that.

The three inputs in this schematic have different values but I did some testing and the 120K resistor worked the best on the input so I put those in all 3 inputs. I think you should also do this if you decide to build this filter because these schematics reflect the circuit that is used in the synthesizer itself and that's why the inputs have different values because they receive signals with different amplitudes. In our synth all the VCO's produce signals with a set amplitude of 10V peak to peak, therefore the input resistors need to be the same value.

There's not much more to say about this. The opamp in the schematics can be any low noise audio type. I used the TL072 for that because I have a lot of those in my components collection and they are the opamps most used in synthesizer projects. But you can also use the TL082 or NE5532.

You can use this filter with a dual 12V powersupply without any changes except for the current limiting resistor to pin 13. Change it from 1K5 to 1K2 for -12V operation.

This filter sounds like a lowpass filter should although it is not as versatile as the Moog or Korg filters. For one, this filter is not self oscillating (at least, the one I build isn't) so you can't make it scream but it does produce that resonant synthesizer sound, if you know what I mean.  It's just a different filter to the Korg or the Moog Ladder Filter which is an other filter I've put in my synth build. It's more a filter to round off certain sounds you've created on your synth, to make them fuller. I don't know, you have to listen to it to know what I'm on about. It should be capable of self oscillation if you read the text that goes with the schematics. The fact that mine didn't self oscillate is probably due to my inexperience at the time I built this.
EDIT 20-March-2020: I just finished work on the Digisound 80.6 lowpass filter using the AS3320 chip and it sounds fenominal. If I were you I would build that filter instead of this one. 

Here are some pictures of the PCB and the panel I made:



The filter is the one on the right. The other one is the VCO. I had yet to add the text to the panels.



You can see the inputs for oscillators one, two and for noise on the left and below that the resonance control voltage input (for the LFO for instance). That input has a level control and there's a switch for internal or external resonance control. On the right is the audio output. The top potmeter is for the Cut-off frequency and the one below is, as mentioned, for resonance.