Showing posts with label MS20. Show all posts
Showing posts with label MS20. Show all posts

Sunday, 5 January 2020

Synthesizer Build part-15: DUAL KORG MS-20 HP/LP FILTER.

This is just two Korg MS-20 filters behind one panel with switches to go between using them as individual filters or switching them in series.  This is one of my early projects so the implementation is a bit clumsy with how I use the switches etc. but it'll be easier to use socket switches instead of toggle switches but in my early building days I didn't know these things. 
I'm keeping the article up for archival reasons plus this dual configuration actually sounds pretty awesome but in hindsight, I wouldn't build it like it's presented below. Just so you know. 

I wasn't too pleased with the performance of the Prophet 5 lowpass filter so I decided to remove it and put a new filter in its place. I've seen lots of videos about the Korg MS-20 and really like the sound of it. I noticed that synthesizer has two nearly identical filters next to eachother; the highpass- and the lowpass-filter, so I wanted to emulate that in my own synth. So I set out to build two of the 'Late MS-20 filters' by Rene Schmitz, and fit them behind a single panel that was the size of the old Prophet 5 filter that I took out. It was a tight fit to put all the knobs and switches on but it worked out beautifully in the end.
The schematics and layout I used are just the same as the ones I used in article 12 of this blog, so if you want to build your own dual filter arrangement you can go to the Korg MS20 filter page and build TWO of those. Build both filters with the HP/LP switch but do not include the bandpass switch. You build two MS-20 HP/LP filters and put them behind one panel. Then, as extra, you add switches to the inputs so you're able to put them in series or use them independently of eachother. The wiring diagram for those switches is further down the article.

Here's a picture of what that looks like. You can see I have filter one on the left side and filter two on the right. Each has its own Cut-Off Frequency and Resonance controls and each has audio and CV-in level controls and each has it's own Highpass/Lowpass switch. Beneath those switches you see two more switches which enable me to switch both filters in series without using patch cables to connect them to eachother.:



The wiring of these two stripboards was a bit of a nightmare but I got it done in the end. I made some initial mistakes and had to re-wire some potmeters so that's why the wires look like such a mess. Luckily it doesn't affect the working of the filter.


In the first filter I used the LM13600 chip and in the second the LM13700 chip. And having them side by side is a good opportunity to compare them and the LM13600 is a bit tamer than the 13700. So if you have both chips in stock you can decide whether you want your filters to sound aggressive or a bit less aggressive. It's not a big difference though.

You can see in the pictures above that it's a tight fit but I did managed to include two volume or level potmeters for the audio inputs, which are not included in the original build but are very useful to have. I'm going to make sure that every filter I build in the future has input level control.
Beneath the HP/LP switches are the two switches that give you the option of using these filters as two stand-alone filters, so not internally connected, or if you want to put them in series so the output of filter 1 goes into the input of filter 2.
One other weird option would be to switch the output of filter 1 to the output jack but leave the input switch for filter 2 as is, so filter 2 has no input. Because these filters are self-oscillating you can now use filter 2 as an oscillator. Put the output into the 4 channel mixer described in article 17 and put the resulting wave through filter 1 or wherever you like. Connect a 1V/Oct voltage to the CV input. Just an idea, but you see there are endless possibilities. That is the beauty of modular synthesizers. :)
However, it would be better to use a single DPDT switch here and use it just to switch between two filters in series or both separate. That makes it easier to switch but that way you can not use one of the filters as stand-alone oscillator, but you won't use that function much anyway I'll bet.

Here is the wiring diagram for those two switches. By all means try and think of a better way to do this. Like I mentioned in the beginning, this was one of my early projects so not everything is perfect. I still get confused by these switches when I use this module after 4 years of using it LOL (I don't use it any more)
Use the switches inside the sockets instead of toggle switches. Much less confusing. But I used the wiring diagram below. 


Finally I want to show you a little video I made which demonstrates the sound of these two filters in series with eachother. I filmed this just after I had finished the build and I was still figuring out what the filter could do but it shows the added benefit of having two of these in series. It can do really deep and full sounding bass tones and it can also scream and distort and sound really weird. I am glad I fitted these and they are certainly a big improvement over the Prophet 5 filter although I will use the AS3320 chip inside it for a future build.
Plus all those knobs and switches so close to eachother look really cool I think ^_____^

Here's a look at the different sounds this filter can produce. (The phaser effects come from the special effects unit and not from this filter):



Okay, that's it for this one. If you enjoyed this article please check out the rest of my synth build and leave me a comment if you have any questions, or even to just say hi. Please also subscribe to my YouTube channel. That would be a great help. THANK YOU!!

Other websites that deal with the DUAL MS-20 configuration:

https://www.modulargrid.net/e/befaco-sallen-key-filter-bf-22

https://www.perfectcircuit.com/signal/korg-ms-20



Sunday, 15 December 2019

Synthesizer Build part-12: THE KORG MS20 FILTER.

A good working version of the famous Korg MS-20 filter by Rene Schmitz, with updated stripboard layout and wiring diagram with LP & HP .
As popular as this filter is, I would not recommend it as your first filter build. Just because of the audio input level behaviour. For your first filter, build the Steiner-Parker diode filter. Instant gratification. 
Now on with our regular program:

There are PCBs available for this VCF. See 'PCB Service'

This is a filter I absolutely had to include in my DIY synthesizer project, for one because Sam Battle from LookMumNoComputer raves about it and it sounds amazing in his videos and the other reason is that it has the option to go between Low-Pass and High-Pass and I didn't have a High-Pass option in the synthesizer yet. I also added the Band-Pass option in the layout drawing however I tested it and it adds no extra benefit to this filter. 
There was a discussion on the Synth DIY Facebook group a while back about the possibility of switching this filter between 6dB per Octave and 12dB per Octave. I've tried it and it works but only in LowPass mode. More about this further down the article.
Btw, I tested this filter on dual 12 Volt and it works just as well as on 15 Volt so no need to change anything if you are feeding it from a +/- 12V powersupply. Of course you need to open Resonance a little more than on 15V but it's all within the normal throw of the potmeters so no problem there.
Btw, eventhough this is THE going design for the OTA version of the MS-20 filter, in my humble opinion it doesn't sound much like a vintage MS-20. But that's just me. It does sound good though so don't get me wrong, you're not waisting your time.

SCHEMATIC:
For this filter I used the 'Late MS20 Filter' schematic from Rene Schmitz which you can find by clicking here. I think he called it the 'late' version because the earlier versions used the Korg MS35 module which was sealed off and what was in it was only revealed in 2000. It was transistor based. The later versions used the OTA chip the LM13600.

This filter is definitely different from other filters. It doesn't sound like the Moog Filter but it does have that 'ripping the fabric of the universe' synth sound and it's a real Speaker Ripper!. It's a 'Sallen-Key' type filter and it produces really divers sounds. (I always think of this filter as the 'Heavy Metal Guitar' pedal of the synthesizer world.) You can get deep bass tones out of it and if you connect an Envelope Generator like the little AD/AR to the CV1 input you'll get a squarewave changing into a really bassy sinewave as the note progresses. It's awesome to experiment with this filter.
In HighPass mode the Cut-Off Frequency potmeter doesn't work over its complete throw. I found it usually only works over the first 50%. This is also true of the other MS-20 filters I built for the Dual version so this is normal behaviour for this design.
This filter is self oscillating in both the Low and High-Pass configuration. The more Resonance you give it, the more the two yellow LED's light up. I found that by using an LM13600 instead of a LM13700 you can  tame the filter a little. The 13600 seems to be a bit less aggressive although the difference is really small. Btw, instead of the TL074 you can also use the TL084 or the LM324. They are pin for pin compatible and work just fine. I personally tested them all successfully.

Here's the original schematic with the pinout numbers for the LM13700:


Here's a link to an image I made showing the switch connections for HP and LP mode: --- click here --

About Resonance and Self-Oscillation:
On the oscilloscope you won't see much Resonance ringing on top of a squarewave in Lowpass mode. I've noticed this with all 3 Korg filters I built so far. Maybe one little sinewave bump on the top left corner of a squarewave but it's not like the ARP or Steiner filters where the whole top and bottom of the squarewave is full of Resonance or self-oscillation. (It gets better with lower input levels though.) But in HiPass mode you get much more. However, this is normal for this filter and it still sounds pretty amazing so this doesn't matter.
Beware this filter does not like high input levels! When I feed it 0-10Vpp squarewaves directly from the Digisound-80 VCO it doesn't work right. It is much happier with the -5/+5Vpp levels of the Thomas Henry 555-VCO. It is always a good idea to put an input level potmeter on the audio input of this filter so you can regulate the input volume. You can try to put a capacitor between 470nF and 1µF on the audio input to block the DC offset voltage of a 0 to 10V signal and turn it into a -5/+5V signal. That should work.
This is a well known characteristic of the Korg MS20 filter. If you increase the level of the audio input you will drown out the resonance of the filter. So you must find a balance between input level and resonance.

6dB vs 12dB.
Although this is a 12dB per Octave filter (2 pole) it is possible to get an output with 6dB per Octave roll-off (1 pole) if you tap the signal from pin 7 of the TL074 (A1 in the schematic drawing) with a 470nF capacitor, just like the normal output. The 6dB however won't work in Highpass mode because the signal is output from the stage before the one where we input the Highpass audio signal.
I have experimented with 6dB and at first I dismissed the option but having recently rebuilt my filter using (vintage) Polystyrene capacitors (and Polyester box caps for the 470nF output caps) it now sounds much better and the 6dB function sounds better too. So I made new layouts which includes the 6dB/Octave function with a switch to give you the choice between 6dB or 12dB. In the rebuilt filter I also used two BC558 transistors that were roughly matched. I'm not sure if this is necessary but it can't hurt. The 6dB/Oct setting sounds more distorted an rough around the edges if you know what I mean. It's a heavier sound. 

ABOUT THE LED's: 
Make sure you use LED's with a voltage drop of around 1,8 Volts. That means Yellow, Green or Red LED's are okay but do NOT USE Bright white LED's or Blue LED's. They have a much higher voltage drop and won't work well in this filter. Remember the LED's replace the original 3 diodes in series. These diodes have a voltage drop of 0,6 Volt so 3 in series means 3 x 0,6Volt = 1,8 Volt.

LAYOUTS:
Below here's the stripboard layout. I made my own version from the ones that are circulating on the internet to which I added the potmeter connections and the audio in and out, CV in, plus the switch connections for Low-, Band- and Highpass with the altered position of the 1nF cap at pin 12 of the LM13700. So with this and the schematics you should have all the info you need to build it right the first time. BTW, the 2 transistors used on the layout below are BC558 PNP's but you can also use the 2N3906 but those have to be put in the other way around. In subsequent builds I used the BC557.
There are simplified layout versions without all the bells and whistles further down the article.



(Last revised 7-Oct.-2023 Cosmetic changes to make layout clearer.)

Please note: I did add the Band-Pass option to the layout but if I were you I would just leave it out. But do some tests and decide for yourself.

About the DPDT switch wiring for HP/LP mode: 
Connect the top two pins and the right middle pin of the High Pass/ Low Pass switch together and connect that to the High-Pass input. You could even just forget about the top right pin and bypass it but I thought it was neater to include it. The lower right pin goes to ground. The audio signal goes into the middle left pin, and the lower left pin goes to the Low-Pass input. The Band-Pass switch is simply connected to the Low-pass input and the audio input. If the filter is in Low-Pass mode the BP switch won't have any effect but in High-Pass mode the switch will connect the audio to the Low-Pass input aswell so both inputs get the audio signal thus creating the bandpass characteristic.
A little sidenote about the writing next to the switch in the layout: the HighPass and LowPass marking next to the switch on the wiring diagram reflect the function of the actual wires connected to that part of the switch. A Toggle switch works the other way around. If you flip the switch upwards, the middle and bottom pins are connected to eachother. If you flip it downwards the top and middle pins are connected so on the eventual panel, the switch should have LowPass marked at the top and HighPass at the bottom.  This way of marking the switch functions goes for all the layouts on this website that have switches in them.

Close up of just the stripboard layout (Print this one and use it for your project. The lay-out is guaranteed, tested and verified faultless. It has been used by hundreds of people by now). Don't forget to cut all the copper strips under the IC's.


(Last revised 7-Oct.-2023 Cosmetic changes. Removed colour codes from resistors, added colour coding to wirebridges.)

Cuts and wirebridges as seen from the COMPONENT SIDE! As always, mark the cuts to be made with a black waterproof Sharpie on the component side. Then put a pin through the marked holes and mark them again on the copper side. Then cut the copper at the marked positions with a sharp, hand held, 6 or 7mm drill bit. Check your cuts with a continuïty meter or a powerful magnifying glass before you proceed.


Bill of Materials:


About the components:
I used fairly cheap LM13700 chips I got out of China via eBay and I think I got lucky and got real ones instead of fakes. But play it safe and get your chips from a reputable source.
I used a DPDT toggle switch (Double Pole Double Throw) to switch between High-Pass and Low-Pass but you could also use a jack socket for High-Pass input with a build-in switch that connects C4 to ground when nothing is plugged in there.
The Cut-Off Frequency potmeter in this build is a 100K one, but you can use any type you wish because pins 1 and 3 are connected to the + and - of the power supply so it is nothing more then a voltage devider. I saw that Sam Battle uses a 4K7 pots for this in his layout so use what ever value you want. (Beware that the voltage difference over that potmeter is 24 Volts so don't go too low with the value or you'll fry your potmeter. Remember Ohm's law!)
I don't think the Resonance potmeter is that critical either but you better stick to the schematics for that one. Keep it a 100K potmeter. I used a logarithmic one but linear will work fine too. As mentioned earlier, you can use an LM13600 instead of the LM13700 and instead of the TL074 you can use the TL084 or the LM324. They all work just fine.
I rebuilt the filter recently and used polystyrene caps instead of ceramics. It did make a difference in my filter but the first version I built of this filter was a mess to look at. Building something neat and tidy always makes it work better I found out. So don't expect miracles by changing the caps from ceramic to polystyrene.
One thing that might be worth experimenting with is the 10K feedback resistor over opamp A3 in the schematic. The one by the LEDs. You could put in a 15K trimpot and see what it does if you change the feedback resistance. I haven't tried this yet myself but it might be worth experimenting with.

SIMPLER LAYOUT VERSIONS OF THE MS-20 FILTER
By request I made a layout with just the lowpass filter, wiring and stripboard only, and I made one with just the lowpass version but including the 6dB or 12dB switch option.
Here's the layout for just the Lowpass version. This is the one that Sam Battle uses in his Kosmo synthesizer:
Wiring diagram:
Stripboard only:

Here's the Lowpass only version but with 6dB and 12dB switch option:
Wiring:
Stripboard only:

PICTURES and DEMO's
Here's a picture of the panel I made for it. Because I recently re-built the filter I had one unused mounting hole left in the panel so I put a white 3mm LED in there. It's a bit bright =)


Below is a picture of the insides. Those big brown Mullard 'tropical fish' caps (so called for their colourful stripes) at the top and bottom are just 100nF caps for de-coupling. They're spread out a bit because they're so big. You can use small ceramic caps for those. I advise to use polystyrene caps for all the other capacitors although that's not necessary for the filter to work. I just found polystyrene caps to sound better but you mustn't attach too much importance to the use of polystyrene caps. They are difficult to find. Any type will do as long as they're not ceramic caps.:


DEMO VIDEOS:
Here's a new demo video I recently made. Just trying out the different functions. I had it connected to the 8 step sequencer. It sounds really awesome but it needs a snappy ADSR input and attenuation on the audio input to make it sound like this:.



This is an old test video, made right at the beginning of when I started building modules. It has the Korg filter (in Highpass mode) and the Moog Ladder filter (in Lowpass) in series and using my 8 step sequencer and reverb from the CaraOK effects module:


Sounds quite good doesn't it? Especially with added echo or phase-shift effects. 

WARNING: Beware your speakers!! This filter can oscillate at below audible frequencies and the cones of your bass speakers will take a hell of a beating if you've got some serious amplification going. If ever a filter could be called a 'Speaker Ripper' this one is it. Quite literally. (I added this warning because tonight I almost blew my speakers up with this filter.)

EXTRA DOCUMENTATION:
I want to direct your attention to a very useful page from Scott Stites' website. He talks about all the different aspects of this filter, using two of these filters in tandem and his approach to adding a Band-Pass mode to it. If you want to build this filter, you have to read this text I think.: Click here for Scott Stites website.

Here is a link to a PDF file called: "A Study of the Korg MS10 and MS20 filters by Timothy E. Stinchcombe --- click here for that PDF ---
It's an in depth study with formulas and schematics, excellent if you're an electronics student and want to get into the details. I must admit it goes way over my head ^__^

Lastly, here's an other very interesting document I found by Sound Semiconductor entitled "Designing Voltage Controlled Filters for Synthesizers with the SSI-2164."
It goes into great detail into how filters work and how to design them and places specific emphasis on the Korg MS-20 filter.

Okay, that's it for this one. If you have any questions or comments then please put them in the comment section below of post them in the special Facebook Discussion and Help Group for this website.
Fun fact: this article is on a solid number two listing of most popular builds on this website, number one being the AS3340 (Digisound-80) VCO. (you know, the really good one.. ^___^  )